Plateau State Polytechnic, Barkin-Ladi Cut Off Mark for 2023/2024 Academic Session – PLAPOLY Cut Off Mark for the current session is officially out. Check below for all you need to know.
Plateau State Polytechnic is a state owned polytechnic in Plateau State, North Central Nigeria. The institution has two campuses, one at Barkin Ladi and the other at Bukuru near Jos, the capital of the state. It provides education to degree and national diploma level. The rector is BLDR. John Dawam.
The institution was founded in 1978 as a College of Technology on the site of Government Technical College, Bukuru. It became a polytechnic in 1980.
READ ALSO – Plateau State Polytechnic (PLAPOLY) Post UTME Form
It may also interest you to know that the institution offers the following courses;
- Agricultural Engineering / Technology
- Banking and Finance
- Building Technology
- Business Administration and Management
- Civil Engineering Technology
- Computer Engineering
- Computer Science
- Electrical Electronics Engineering
- Foundry Technology
- Hospitality Management
- Leisure and Tourism
SEE ALSO – Cut off Mark for Engineering in all Schools (JAMB and Post UTME)
- Library and Information Science
- Local Government Studies
- Mechanical Engineering Technology
- Metallurgy
- Mineral Resources and Engineering Technology
- Office Technology and Management
- Public Administration
- Quantity Surveying
- Science Laboratory Technology
- Social Development
- Statistics
- Urban and Regional Planning
PLAPOLY Cut Off Mark 2023/2024
The management of the well known Plateau State Polytechnic, Barkin-Ladi has officially published the school’s cut off mark for the 2022/2023 academic session. This is the minimum required JAMB UTME score necessary for admission into any higher institution of learning such as a university, polytechnic, college, etc. To know the current and approved minimum entrance score alias cut off mark for Plateau State Polytechnic, Barkin-Ladi, kindly check below.
SEE ALSO – Universities, Polytechnics, Colleges of Education That Accept Low Jamb Score
PLAPOLY Cut Off Mark 2023/2024
120
The Plateau State Polytechnic, Barkin-Ladi has considerably and graciously pegged her cut off mark for the 2022/2023 academic session at 120 and above. This is to avail all interested candidates the opportunity to higher education in the college. In line with the Joint Admission and Matriculation Board (JAMB), Plateau State Polytechnic, Barkin-Ladi is ready to welcome applications from suitably qualified candidates seeking for admission into the school.
Beside the general cut off mark, emphasis are also placed on the course/department of study the candidates apply for. See below for details.
SEE ALSO – JAMB Subject Combination for Accounting / Accountancy
PLAPOLY Departmental Cut Off Mark 2023/2024
See table below to know the score applicable to your course/department of interest:
COURSES | MINIMUM JAMB CUT OFF MARK |
Accountancy | 120 and above |
Agricultural Engineering / Technology | 120 and above |
Banking And Finance | 120 and above |
Building Technology | 120 and above |
Business Administration and Management | 120 and above |
Chemical Engineering Technology | 120 and above |
Computer Engineering | 120 and above |
Computer Science | 120 and above |
Electrical and Electronic Engineering | 120 and above |
Civil Engineering | 120 and above |
Urban and Regional Planning | 120 and above |
Foundry Engineering Technology | 120 and above |
Hospitality Management | 120 and above |
Leisure And Tourism management | 120 and above |
Marketing | 120 and above |
Mechanical Engineering Technology | 120 and above |
Metallurgical Engineering Technology | 120 and above |
Office Technology And Management | 120 and above |
Public Administration | 120 and above |
Quantity Surveying | 120 and above |
Science Laboratory Technology | 120 and above |
Social Development | 120 and above |
Statistics | 120 and above |
Urban and Regional Planning | 120 and above |
Mineral and Petroleum Resource Engineering | 120 and above |
SEE ALSO – JAMB Subject Combination for Wood Production Engineering
Be the first to comment